Introduction to IEEE Standards and the Recent Revisions of IEEE 1584 - Arc Flash Calculations

Share

Southern Alberta is pleased to host Daleep Mohla, Chair of the IEEE 1584 Working Group, and Wei-Jen Lee, IEEE IAS President-Elect, for a seminar discussing the changes in the 2018 revision of IEEE 1584.  The seminar begins with an introduction to the IEEE Standards Association, and the standards development process.

 

Join us to hear about important changes to IEEE 1584, and this unique opportunity to ask your questions directly to members of the Working Group.


Advance registration only. Registration at the door is not available for this presentation.

Participants must sign-in at the Security Desk in the T2 Building prior to the seminar, and must sign-out upon leaving.


Please indicate any food allergies or dietary restrictions under "Special Requests" when registering.


Registration consists of two parts - vTools and PayPal. Follow the "Register Now" link below, and complete the information. The system will then take you to a PayPal page to enter your payment information. When you have successfully registered and paid, you will receive 2 confirmation emails, 1 from IEEE and 1 from PayPal. Your registration is not complete until your payment has been received, and you have received both confirmation emails.



  Date and Time

  Location

  Contact

  Registration



  • 110 - 12th Avenue SW
  • Calgary, Alberta
  • Canada
  • Building: TransAlta "T1" building
  • Room Number: T1-Auditorium
  • Co-sponsored by IEEE Standards Association and TransAlta
  • Starts 28 June 2019 12:00 PM
  • Ends 28 July 2019 11:59 PM
  • All times are Canada/Mountain
  • Admission fee ?
  • Register


  Speakers

Daleep Mohla

Daleep Mohla of DCM Electrical Consulting Services, Inc.

Biography:

Daleep Mohla, (S’72-M’73-SM’01, F’06, LF’12) Principal Consultant DCM Electrical Consulting Services Inc. received a BSEE degree from West Virginia Institute of Technology, WV in 1973. He is chair of IEEE 1584WG and a member of NFPA 70E Standard for Electrical Safety in the Workplace and chair of the Industrial Applications Society (IAS) Standards Department. He was employed with Union Carbide and Dow for over 30 years

As the Owner and Principal consultant for DCM Electrical Consulting Services, Inc., Daleep is now engaged in conducting training on National Electrical Code and NFPA 70E, and preparation and auditing of safety programs for industrial and commercial customers. He is a Registered Professional Engineer in the State of Texas.

Address:Texas, United States

Wei-Jen Lee

Wei-Jen Lee of University of Texas at Arlington

Biography:

Wei-Jen Lee, (S’85M’85–SM’97–F’07) received the B.S. and M.S. degrees from National Taiwan University, Taipei, Taiwan, in 1978 and 1980, respectively, and the Ph.D. degree from the University of Texas at Arlington, Arlington, TX, USA, in 1985, all in electrical engineering.

He is currently a Professor with the Department of Electrical Engineering and the Director of the Energy Systems Research Center, University of Texas at Arlington. Since 2008, he has also been serving as a Project Manager for the IEEE/National Fire Protection Association Arc Flash Research Project. He has been involved in research on arc flash and electrical safety, utility deregulation, renewable energy, smart grid, microgrid, load forecasting, power quality, distribution automation and demand-side management, power systems analysis, online real-time equipment diagnostic and prognostic systems, and microcomputer-based instrumentation for power systems monitoring, measurement, control, and protection.

Dr. Lee is a registered Professional Engineer in the state of Texas. Dr Lee is President- elect of Industrial Applications Society (IAS).

Address:Texas, United States





Agenda

  • 5:45pm: Doors open
  • 5:45-6:20pm: Networking and a Light Meal
  • 6:20-6:30pm: Opening comments
  • 6:30-6:50pm: IEEE-SA and CAG Introduction
  • 6:50-8:25pm: IEEE 1584 - Changes in the recent revision
  • 8:25-8:30pm: Closing comments